Manx SA7x Guía de instalación Pagina 82
- Pagina / 320
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3.25 External Sense Connector (J14)
3.25 External Sense Connector (J14)
This two-pin male receptacle (J14) on the back of the 887–C power controller
attaches to Digital cable connector part number 12–10821–02 with connector
pin sockets A–PS–1209379–0–0. It removes power from the loads when
enabled by an external sensor. Conditions that a sensor may detect include
system over temperature or system air-flow loss. To engage the external sense,
plug an appropriate sensor (one that presents a switch closure in the event of
an out-of-tolerance condition) into the two pins on the connector. To reset the
external sense, cycle the circuit breaker off and then back on again.
WARNING
Do not rely on the external sense control to isolate hazardous voltages
from the system. Use the circuit breaker to isolate all hazardous
voltages.
3.26 Power Controller Circuit Breaker
The power controller circuit breaker has two positions: 0 and 1. The 0 position
represents OFF and the 1 position represents ON.
3.27 887–C Power Controller Cable (Cordage)
The 887–C power controller requires power connector cable replacement to
accommodate international power requirements and power connector plug
configurations. Table 3–7 lists the cable (cordage) part numbers for some
countries using 220/240 Vac power applications.
Table 3–7 887–C Power Controller 220/240 Vac Power Cable Variations
part number Country
17–01255–01 Europe, U.S., Japan (IEC 309 plug and cordage)
17–00199–10 Central Europe (Schuko-plug)
17–00198–05 Australia
17–00364–06 Italy
17–00209–05 United Kingdom
3–40 Preparation and Installation
- Sx300 Storage Array 1
- Installation Guide 1
- Contents 3
- Elements 6
- Configuration 8
- Related Documents 16
- Documentation Conventions 16
- General Information 17
- 1.1 Product Descriptions 18
- 1.2 DECArray300 Specifications 23
- 1.3 Acoustic Noise Values 26
- 1.4 EMC/EMI 27
- 1–12 General Information 28
- General Information 1–13 29
- 1–14 General Information 30
- General Information 1–15 31
- 1.6 Thermal Stabilization 32
- Storage Array 33
- SHIPPING 36
- CXO-688C_S 37
- SHR_X1103_89_SCN 37
- CXO-924A_S 38
- SHR_X1104_89_SCN 38
- CXO-395C_S 39
- SHR_X1105_89_SCN 39
- Preparation and Installation 43
- 3.3 Electrostatic Discharge 48
- 3.5 Mounting the Half Bezel 52
- Figure 3–3 Rear Access Panel 54
- 3.11 Ground Wire 55
- 3.16.1 Chassis Rail Assembly 63
- 3.19 Applying Power 75
- 3.20 Power Controller 75
- 3.23 BUS/OFF/ON Switch (S1) 80
- 6000 System 85
- 4.1.2 Dual-Host Configurations 86
- SHR_X1127A_89 89
- SHR_X1128C_89 96
- SHR_X1128_89 99
- SHR-X0121-90 103
- LABEL AREA 103
- DSSI TERMINATOR 103
- SHR-X0108-90 105
- OPERATOR CONTROL PANEL 106
- 5.1 Steps to Install 108
- 5.1.4 Installation Procedure 116
- SHR-X0124-90 118
- SHR_X1113_89_SCN 121
- SHR-X0126A-90 122
- SHR-X0127A-90 123
- SHR-X0122-90 129
- 5.2.2 Dual-Host Configuration 135
- 5.3 Powering Up the SF7x 149
- 5.4.1 Filling Out the Labels 150
- 5.4.2 Labeling the Cables 150
- 5.4.3 Labeling the OCP 150
- 5.5 Final Verification 152
- 6.1 Steps to Install 154
- 6.1.4 Installation Procedure 160
- CONNECTORS 167
- AC RECEPTACLE 167
- AC POWER 167
- 6.2.2 Dual-Host Configuration 172
- 6.4.1 Filling Out the Labels 176
- 6.4.2 Labeling the Cables 177
- 6.5 Final Verification 179
- SDI Storage Elements 181
- CABINET 183
- 7.3.1 Hardware Check list 184
- 7.3.3 Electrostatic Discharge 188
- Installation Troubleshooting 193
- 2. Remove the Rx7x disk ISE 197
- SHR-X0135A-90 199
- SHR-X0135-90 200
- SHR-X0136A-90 200
- SKID PLATE 201
- 8.2.2 Fault Matrix 205
- 8.2.3 Error Conditions 206
- • Poor power or grounding 207
- 8.2.5 Soft Error Rates 208
- Diagrams 209
- A.1.2 Dual Host Configurations 210
- A.1.3 Stripeset Configurations 211
- A.1 General Cabling Rules 212
- A.2 Cabling Diagrams 213
- A.3 Single-Host Configurations 214
- A.4 Dual-Host Configurations 239
- Enclosure 266
- B.3 Powering Up the ISEs 269
- C.2 Conversion Procedure 276
- C.2.4 Labeling the Cables 283
- C.2.7 Final Verification 291
- SHR_X1128B_89 297
Relacionado con productos y manuales para Cajas eléctricas Manx SA7x
Cajas eléctricas Manx SA7x Guía de instalación
(52 paginas)
(52 paginas)
Cajas eléctricas Manx SA7x Manual de servicio
(128 paginas)
(128 paginas)
Cajas eléctricas Manx SA7x Especificaciones
(170 paginas)
(170 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales