3 Preparation and Installation
3.1 Add-On Disk or Tape Drive Order Sequence . . . . . . . . . . . . . . . . 3–1
3.2 Add-On Disk or Tape Drive Positions . . . . . . . . . . . . . . . . . . . . . . 3–4
3.3 Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–6
3.4 Removing and Replacing the Cabinet Front Bezels . . . . . . . . . . . 3–7
3.5 Mounting the Half Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
3.6 Removing and Replacing the OCP . . . . . . . . . . . . . . . . . . . . . . . . 3–10
3.7 Removing and Replacing the Cabinet Top Cover . . . . . . . . . . . . . 3–11
3.8 Removing and Replacing the Cabinet Rear Access Panel . . . . . . . 3–11
3.9 Removing and Replacing the Cabinet Kick Plate . . . . . . . . . . . . . 3–13
3.10 Stabilizer Plate (Weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–13
3.11 Ground Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–13
3.12 Installing Cabinet Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–14
3.13 Guide Rail Plate Installation (RETMA Rails) . . . . . . . . . . . . . . . 3–15
3.14 Left Position Guide Rail Plate Installation . . . . . . . . . . . . . . . . . 3–15
3.15 Right Position Guide Rail Plate Installation . . . . . . . . . . . . . . . . 3–19
3.16 Chassis Rail Installation (Universal Rails) . . . . . . . . . . . . . . . . . 3–20
3.16.1 Chassis Rail Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–21
3.16.2 Right Position Chassis Rail Assembly Installation . . . . . . . . . 3–23
3.16.3 Left Position Chassis Rail Assembly Installation . . . . . . . . . . 3–26
3.17 Placing the Add-On Storage Element into the Cabinet . . . . . . . . 3–29
3.18 Cable and Power Cord Routing and Connections . . . . . . . . . . . . . 3–33
3.19 Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–33
3.20 Power Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–33
3.21 External Sense Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–37
3.22 Power Controller Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–37
3.23 BUS/OFF/ON Switch (S1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–38
3.24 Power Control Bus (Front Panel J10, J11) . . . . . . . . . . . . . . . . . . 3–39
3.25 External Sense Connector (J14) . . . . . . . . . . . . . . . . . . . . . . . . . . 3–40
3.26 Power Controller Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . 3–40
3.27 887–C Power Controller Cable (Cordage) . . . . . . . . . . . . . . . . . . . 3–40
4 Installing an SF3xx Storage Array to a VAX 6000 System
4.1 Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
4.1.1 Single-Host Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
4.1.2 Dual-Host Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
4.2 Single-Host Installation of an SF3xx Storage Array . . . . . . . . . . . 4–2
4.2.1 Inspecting the Storage Array (Single-Host) . . . . . . . . . . . . . . 4–3
4.2.2 Cabling the Storage Array (Single-Host) . . . . . . . . . . . . . . . . 4–7
iv
Comentarios a estos manuales