Manx SA7x Guía de instalación Pagina 187
- Pagina / 320
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7.3 Add-On of SDI Disk Drive Installation
7.3.2 Add-On Disk Drive Installation
Unpack the add-on disk drive and complete the thermal stabilization per
the procedures in Chapter 1. Make sure all add-on disk drive and cabinet
hardware is available before beginning installation procedures. Refer to
Section 7.3.1.
The following sections describe the add-on disk drive installation tasks.
Note
For the add-on storage element or sequence for the DECArray300
cabinet, refer to Chapter 3.
1. Upper Level Disk Drive Installation
Only valid for RA9x Drives : When installing an add-on disk drive in the
left-hand, disk drive position 5 of the cabinet, it is necessary to remove the
cabinet top cover. The drive chassis stabilizer bracket cannot be removed
from the frame and attached to the upper level disk drives without first
removing the cabinet top cover refer to Section 3.7.
Each upper level disk drive is supported by two chassis retainer brackets
(top and bottom), and two (top and bottom) factory-installed rear lock-
down brackets with one U-clip each (only RA9x). Detailed instructions for
removing / installing this hardware are found in Section 3.12 and 3.17.
The RA9x disk drives will be supported by two chassis stabilizer brackets.
Note
An DECArray300 cabinet system with only one disk drive in disk drive
position 5 or 1 will have a 25-pound stabilizer plate (weight) attached
to the underside of the upper cabinet H-stiffener.
2. Center Level Disk Drive Installation
When installing an add-on disk drive in the center level of the cabinet
(disk drive position 3 or 4), each disk drive is supported by two chassis
retainer brackets (top and bottom), and two factory-installed rear lock-
down brackets (top and bottom) with one U-clip each (only RA9x). Detailed
instructions for removing / installing this hardware are described in Section
3.12 and 3.17.
Chassis stabilizer brackets are not used for center level disk drive support
in this cabinet.
Installation and Preparation of the Add-On SDI Storage Elements 7–7
- Sx300 Storage Array 1
- Installation Guide 1
- Contents 3
- Elements 6
- Configuration 8
- Related Documents 16
- Documentation Conventions 16
- General Information 17
- 1.1 Product Descriptions 18
- 1.2 DECArray300 Specifications 23
- 1.3 Acoustic Noise Values 26
- 1.4 EMC/EMI 27
- 1–12 General Information 28
- General Information 1–13 29
- 1–14 General Information 30
- General Information 1–15 31
- 1.6 Thermal Stabilization 32
- Storage Array 33
- SHIPPING 36
- CXO-688C_S 37
- SHR_X1103_89_SCN 37
- CXO-924A_S 38
- SHR_X1104_89_SCN 38
- CXO-395C_S 39
- SHR_X1105_89_SCN 39
- Preparation and Installation 43
- 3.3 Electrostatic Discharge 48
- 3.5 Mounting the Half Bezel 52
- Figure 3–3 Rear Access Panel 54
- 3.11 Ground Wire 55
- 3.16.1 Chassis Rail Assembly 63
- 3.19 Applying Power 75
- 3.20 Power Controller 75
- 3.23 BUS/OFF/ON Switch (S1) 80
- 6000 System 85
- 4.1.2 Dual-Host Configurations 86
- SHR_X1127A_89 89
- SHR_X1128C_89 96
- SHR_X1128_89 99
- SHR-X0121-90 103
- LABEL AREA 103
- DSSI TERMINATOR 103
- SHR-X0108-90 105
- OPERATOR CONTROL PANEL 106
- 5.1 Steps to Install 108
- 5.1.4 Installation Procedure 116
- SHR-X0124-90 118
- SHR_X1113_89_SCN 121
- SHR-X0126A-90 122
- SHR-X0127A-90 123
- SHR-X0122-90 129
- 5.2.2 Dual-Host Configuration 135
- 5.3 Powering Up the SF7x 149
- 5.4.1 Filling Out the Labels 150
- 5.4.2 Labeling the Cables 150
- 5.4.3 Labeling the OCP 150
- 5.5 Final Verification 152
- 6.1 Steps to Install 154
- 6.1.4 Installation Procedure 160
- CONNECTORS 167
- AC RECEPTACLE 167
- AC POWER 167
- 6.2.2 Dual-Host Configuration 172
- 6.4.1 Filling Out the Labels 176
- 6.4.2 Labeling the Cables 177
- 6.5 Final Verification 179
- SDI Storage Elements 181
- CABINET 183
- 7.3.1 Hardware Check list 184
- 7.3.3 Electrostatic Discharge 188
- Installation Troubleshooting 193
- 2. Remove the Rx7x disk ISE 197
- SHR-X0135A-90 199
- SHR-X0135-90 200
- SHR-X0136A-90 200
- SKID PLATE 201
- 8.2.2 Fault Matrix 205
- 8.2.3 Error Conditions 206
- • Poor power or grounding 207
- 8.2.5 Soft Error Rates 208
- Diagrams 209
- A.1.2 Dual Host Configurations 210
- A.1.3 Stripeset Configurations 211
- A.1 General Cabling Rules 212
- A.2 Cabling Diagrams 213
- A.3 Single-Host Configurations 214
- A.4 Dual-Host Configurations 239
- Enclosure 266
- B.3 Powering Up the ISEs 269
- C.2 Conversion Procedure 276
- C.2.4 Labeling the Cables 283
- C.2.7 Final Verification 291
- SHR_X1128B_89 297
Relacionado con productos y manuales para Cajas eléctricas Manx SA7x
Cajas eléctricas Manx SA7x Guía de instalación
(52 paginas)
(52 paginas)
Cajas eléctricas Manx SA7x Manual de servicio
(128 paginas)
(128 paginas)
Cajas eléctricas Manx SA7x Especificaciones
(170 paginas)
(170 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales