Manx SA7x Guía de instalación Pagina 296
- Pagina / 320
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
D.1 Single-System Installation of an DECarray
This section provides the procedures for installing the DECarray in a single-
system configuration correctly and safely. Digital Multivendor Customer
Services or trained installing personnel must perform the procedures.
Make sure that all precautions for site preparation have been completed.
The procedures provide the steps to:
• Inspecting the array for proper configuration (Section D.1.1)
• Cable the DECarray with an existing VAX 4000 system in the single-
system configuration (Section D.1.2)
• Verify the DECarray for correct operation (Section D.1.3)
D.1.1 Inspecting the Storage Array (Single-System)
This procedure describes the steps to inspect the DECarray for correct
configuration.
At the front of the DECarray:
a. The DSSI ID switches behind the door of the operator control panel (OCP)
of every SF7x enclosure installed are set according to Table D–1 and
Figure D–2.
b. The Mass Storage Control Protocol (MSCP) switch (right-most switch of
each switch pack) should be in the down or enabled position at all times
unless you are instructed to change it to the up or disabled position.
Table D–1 SF7x DSSI ID Verification (Front View)
Positions 1, 2, 4, and 7
1
MSCP
Switch
Settings
Corresponding
DSSI ID Number
Left Rear (LR)
Left Front (LF)
Right Front (RF)
Right Rear (RR)
0
0
0
0
001
010
011
100
1
2
3
4
Positions 3 and 8
1
MSCP
Switch
Settings
Corresponding
DSSI ID Number
1
The switch settings for OCPs in these positions are 0 = down and 1 = up.
(continued on next page)
D–4 Installing a DECarray with VAX 4000 Systems
- Sx300 Storage Array 1
- Installation Guide 1
- Contents 3
- Elements 6
- Configuration 8
- Related Documents 16
- Documentation Conventions 16
- General Information 17
- 1.1 Product Descriptions 18
- 1.2 DECArray300 Specifications 23
- 1.3 Acoustic Noise Values 26
- 1.4 EMC/EMI 27
- 1–12 General Information 28
- General Information 1–13 29
- 1–14 General Information 30
- General Information 1–15 31
- 1.6 Thermal Stabilization 32
- Storage Array 33
- SHIPPING 36
- CXO-688C_S 37
- SHR_X1103_89_SCN 37
- CXO-924A_S 38
- SHR_X1104_89_SCN 38
- CXO-395C_S 39
- SHR_X1105_89_SCN 39
- Preparation and Installation 43
- 3.3 Electrostatic Discharge 48
- 3.5 Mounting the Half Bezel 52
- Figure 3–3 Rear Access Panel 54
- 3.11 Ground Wire 55
- 3.16.1 Chassis Rail Assembly 63
- 3.19 Applying Power 75
- 3.20 Power Controller 75
- 3.23 BUS/OFF/ON Switch (S1) 80
- 6000 System 85
- 4.1.2 Dual-Host Configurations 86
- SHR_X1127A_89 89
- SHR_X1128C_89 96
- SHR_X1128_89 99
- SHR-X0121-90 103
- LABEL AREA 103
- DSSI TERMINATOR 103
- SHR-X0108-90 105
- OPERATOR CONTROL PANEL 106
- 5.1 Steps to Install 108
- 5.1.4 Installation Procedure 116
- SHR-X0124-90 118
- SHR_X1113_89_SCN 121
- SHR-X0126A-90 122
- SHR-X0127A-90 123
- SHR-X0122-90 129
- 5.2.2 Dual-Host Configuration 135
- 5.3 Powering Up the SF7x 149
- 5.4.1 Filling Out the Labels 150
- 5.4.2 Labeling the Cables 150
- 5.4.3 Labeling the OCP 150
- 5.5 Final Verification 152
- 6.1 Steps to Install 154
- 6.1.4 Installation Procedure 160
- CONNECTORS 167
- AC RECEPTACLE 167
- AC POWER 167
- 6.2.2 Dual-Host Configuration 172
- 6.4.1 Filling Out the Labels 176
- 6.4.2 Labeling the Cables 177
- 6.5 Final Verification 179
- SDI Storage Elements 181
- CABINET 183
- 7.3.1 Hardware Check list 184
- 7.3.3 Electrostatic Discharge 188
- Installation Troubleshooting 193
- 2. Remove the Rx7x disk ISE 197
- SHR-X0135A-90 199
- SHR-X0135-90 200
- SHR-X0136A-90 200
- SKID PLATE 201
- 8.2.2 Fault Matrix 205
- 8.2.3 Error Conditions 206
- • Poor power or grounding 207
- 8.2.5 Soft Error Rates 208
- Diagrams 209
- A.1.2 Dual Host Configurations 210
- A.1.3 Stripeset Configurations 211
- A.1 General Cabling Rules 212
- A.2 Cabling Diagrams 213
- A.3 Single-Host Configurations 214
- A.4 Dual-Host Configurations 239
- Enclosure 266
- B.3 Powering Up the ISEs 269
- C.2 Conversion Procedure 276
- C.2.4 Labeling the Cables 283
- C.2.7 Final Verification 291
- SHR_X1128B_89 297
Relacionado con productos y manuales para Cajas eléctricas Manx SA7x
Cajas eléctricas Manx SA7x Guía de instalación
(52 paginas)
(52 paginas)
Cajas eléctricas Manx SA7x Manual de servicio
(128 paginas)
(128 paginas)
Cajas eléctricas Manx SA7x Especificaciones
(170 paginas)
(170 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales