Manx SA7x Guía de instalación Pagina 117
- Pagina / 320
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5.1 Steps to Install
5.1.4.1 Preparing the Sx300 Storage Array
The following procedure describes how to prepare the array to receive the SF7x
storage enclosure(s):
1. Place the SF7x to be installed to one side, in front of the array cabinet.
2. Open the front and rear bezels of the storage array.
5.1.4.2 Hardware Installation Procedures
Perform the following steps in full and in the order presented.
WARNING
Before performing the following steps, refer to the system documenta-
tion for the correct steps to perform an orderly shutdown of the system
that the storage array is connected to.
1. Install the ac power cord (only for 220/240 Vac version):
a. Go to rear of cabinet. Open the Back panel by loosening the two captive
screws on the top.
CAUTION
Use care not to disturb or damage power cords and DSSI cables that
are already connected to the DSSI I/O panel.
b. Leave approximately 0.6 meter (2 feet) of slack at the position location.
c. Connect the male end of the ac power cord to the first available outlet
on the power controller.
d. Install the slide mount and associated hardware. Refer to Figure 3–9
and Chapter 3.
2. Position the OCP.
a. Adjust the SF7x OCP mount, Figure 5–4, to the LEFT for positions
SF1, SF4, SF6 and to the RIGHT for positions SF2, SF3, SF5.
b. Check that this and all other OCPs and magazine tape subsystem
fronts project through the front bezels of the storage array correctly.
Installing the SF7x Storage Enclosure in an Sx300 Storage Array 5–11
- Sx300 Storage Array 1
- Installation Guide 1
- Contents 3
- Elements 6
- Configuration 8
- Related Documents 16
- Documentation Conventions 16
- General Information 17
- 1.1 Product Descriptions 18
- 1.2 DECArray300 Specifications 23
- 1.3 Acoustic Noise Values 26
- 1.4 EMC/EMI 27
- 1–12 General Information 28
- General Information 1–13 29
- 1–14 General Information 30
- General Information 1–15 31
- 1.6 Thermal Stabilization 32
- Storage Array 33
- SHIPPING 36
- CXO-688C_S 37
- SHR_X1103_89_SCN 37
- CXO-924A_S 38
- SHR_X1104_89_SCN 38
- CXO-395C_S 39
- SHR_X1105_89_SCN 39
- Preparation and Installation 43
- 3.3 Electrostatic Discharge 48
- 3.5 Mounting the Half Bezel 52
- Figure 3–3 Rear Access Panel 54
- 3.11 Ground Wire 55
- 3.16.1 Chassis Rail Assembly 63
- 3.19 Applying Power 75
- 3.20 Power Controller 75
- 3.23 BUS/OFF/ON Switch (S1) 80
- 6000 System 85
- 4.1.2 Dual-Host Configurations 86
- SHR_X1127A_89 89
- SHR_X1128C_89 96
- SHR_X1128_89 99
- SHR-X0121-90 103
- LABEL AREA 103
- DSSI TERMINATOR 103
- SHR-X0108-90 105
- OPERATOR CONTROL PANEL 106
- 5.1 Steps to Install 108
- 5.1.4 Installation Procedure 116
- SHR-X0124-90 118
- SHR_X1113_89_SCN 121
- SHR-X0126A-90 122
- SHR-X0127A-90 123
- SHR-X0122-90 129
- 5.2.2 Dual-Host Configuration 135
- 5.3 Powering Up the SF7x 149
- 5.4.1 Filling Out the Labels 150
- 5.4.2 Labeling the Cables 150
- 5.4.3 Labeling the OCP 150
- 5.5 Final Verification 152
- 6.1 Steps to Install 154
- 6.1.4 Installation Procedure 160
- CONNECTORS 167
- AC RECEPTACLE 167
- AC POWER 167
- 6.2.2 Dual-Host Configuration 172
- 6.4.1 Filling Out the Labels 176
- 6.4.2 Labeling the Cables 177
- 6.5 Final Verification 179
- SDI Storage Elements 181
- CABINET 183
- 7.3.1 Hardware Check list 184
- 7.3.3 Electrostatic Discharge 188
- Installation Troubleshooting 193
- 2. Remove the Rx7x disk ISE 197
- SHR-X0135A-90 199
- SHR-X0135-90 200
- SHR-X0136A-90 200
- SKID PLATE 201
- 8.2.2 Fault Matrix 205
- 8.2.3 Error Conditions 206
- • Poor power or grounding 207
- 8.2.5 Soft Error Rates 208
- Diagrams 209
- A.1.2 Dual Host Configurations 210
- A.1.3 Stripeset Configurations 211
- A.1 General Cabling Rules 212
- A.2 Cabling Diagrams 213
- A.3 Single-Host Configurations 214
- A.4 Dual-Host Configurations 239
- Enclosure 266
- B.3 Powering Up the ISEs 269
- C.2 Conversion Procedure 276
- C.2.4 Labeling the Cables 283
- C.2.7 Final Verification 291
- SHR_X1128B_89 297
Relacionado con productos y manuales para Cajas eléctricas Manx SA7x
Cajas eléctricas Manx SA7x Guía de instalación
(52 paginas)
(52 paginas)
Cajas eléctricas Manx SA7x Manual de servicio
(128 paginas)
(128 paginas)
Cajas eléctricas Manx SA7x Especificaciones
(170 paginas)
(170 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales